Stop Losing Screws Off The Bit Mid-Drive
One hand on the wood, one hand on the drill, and the screw drops the second you reach overhead or hit hardwood. MagGrip Pro keeps it locked until you're done.
- Never lose a screw off the bit again
- Slides onto any standard bit in seconds
- Works with any standard hex-shank bit
- 2-pack included, always a spare on hand
Backed by a 90-day money-back guarantee
You already know this moment
One hand on the wood, one hand on the drill, and the screw just won't stay on. It keeps dropping, especially with long screws or when you're up on a ladder.
Even magnetic bits still fall off. That's not bad luck. A regular magnetic bit touches the screw at one small point, so the moment you tip the drill or push into hardwood, it lets go.
How it actually holds
It's the difference between a magnet taped near a fridge door and one pressed flat against it. One barely holds. The other locks on.
-
1
Slide it on
Fits over any standard hex-shank bit in seconds. No tools, no rewiring, no extra parts.
-
2
The magnet wraps the tip
A regular bit's magnet sits off to the side. This sleeve wraps directly around the driving tip, so it grips the screw right where it's seated instead of reaching for it at an angle.
-
3
Drive with one hand
Overhead, into hardwood, in a tight blind spot, the screw stays locked to the tip until it's fully driven.
Built for the jobs you actually do
Ladders, hardwood framing, tight corners behind cabinets. This is tested on real job sites, not a bench in a studio.
No tools, no setup
Slide it over your bit and it's ready. No rewiring, no extra parts, nothing to charge or configure.
Stronger hold, tested hard
We hammer it, shake it, and drive it straight into hardwood. The screw stays locked to the tip the whole time, not just in a sales photo.
Why this works when a regular magnetic bit doesn't
Wraps the full tip
Not a single embedded point like most magnetic bits. The sleeve surrounds the driving tip, so contact holds even at an angle.
Hammer and shake tested
We test it under force, not just in a hand. The screw stays put through hardwood, overhead reaches, and rough handling.
Built for big and small screws
Long framing screws, short trim screws, the hold stays the same whether it's a large head or a tiny one.
Two to a box
One for the drill, one as a spare in your bag or on the truck, so you're never left without one.
MagGrip Pro vs. a regular magnetic bit
| MagGrip Pro | Regular magnetic bit | |
|---|---|---|
| Magnet contact with the screw | Wraps the full tip | Small embedded point |
| Holds through a hammer and shake test | Not tested | |
| Stays on through hardwood and overhead work | Often falls off | |
| Comes with a spare | 2-pack | Usually sold single |
Get your MagGrip Pro
$19.99 β includes 2 bits, one black, one green
- Fits any standard hex-shank bit
- Ships in 1-2 days
- 90-day money-back guarantee
Not holding up on your job? Full refund within 90 days.
Questions before you order
Will it fit the drill or driver I already own?
Yes. MagGrip Pro fits any standard hex-shank bit, corded or cordless, regardless of brand.
I already have magnetic bits. Why would this be any different?
A regular magnetic bit touches the screw at one small point, so it lets go the moment you tip the drill or push into hardwood. MagGrip Pro's sleeve wraps the full driving tip instead, so the grip holds at an angle, not just straight on.
Does it actually hold up, or is this another gadget that looks good on video?
We test every batch with a hammer and shake test, driving straight into hardwood. The screw stays on the tip through all of it, not just in a demo clip.
Do I need any tools or rewiring to install it?
No. It slides directly over your bit in seconds. No tools, no extra parts, nothing to set up.
Can't I just hold the screw with my free hand instead?
You can, but it means two hands tied up and a real risk of catching your fingers when the bit slips. MagGrip Pro keeps the screw locked to the tip so you can drive one-handed, even overhead or in a blind spot.
How big or small a screw will it hold?
It's built to hold both long framing screws and short trim screws without losing grip.
How fast will it ship, and where does it ship from?
Orders are processed in 1 to 2 days and arrive 5 to 10 days after processing.
What if it doesn't work for me?
You're covered by a 90-day money-back guarantee. If it's not holding up on your job, send it back for a full refund.
Trusted on job sites everywhere
"Haven't dropped a screw off the bit since I put this on."
"Fit my driver right out of the box, no fuss."
"Overhead electrical work finally doesn't need three hands."
"Held through hardwood all day without slipping once."
"Whole crew wants their own pair now."
"Second one lives in my spare bag, exactly as it should."
Stop losing screws off the bit for good
One hand free, every drive, on every job. $19.99, backed by a 90-day guarantee.